• montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a
  • montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a
  • montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a
  • montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a
montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a

montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a

Detalhes do produto:

Marca: Gold
Certificação: ISO9001:2000，EU, UL,CUL,RoHS
Número do modelo: SAQ2402D SAl4002D SAl4005D SAE4005D
Melhor preço Contato

Informação detalhada
nome: C.A. SSR do relé da C.A. SSR de único duplo na linha certificado: ISO9001: 2000, UE, UL, CUL, RoHS
Tensão da carga: 24-280VAC ou 40-480VAC Aposta do isolamento. Em & para fora: Isolamento ótico ≥2000VAC 1min
Isolamento ao caso: ≥2500VAC 1min Controle a tensão: 3-15VDC ou 15-28VDC
Controle atual: 6-25mA precisam a corrente do limite Tensão de ligação: ≤1.1VAC
escapamento do Fora-estado: ≤0.5mA Fora-estado dv/dt: 300v/μs
Tempo de ligar/desligar: 10ms Escala de Frequenty: 47/63Hz
Temperatura de funcionamento: -50~80℃ Dispositivo real interno (TRIAC): 3A (1.2A atual a longo prazo)
Aplicações: Bobina do contator, eletroímã, micro-motor da C.A., aquecimento. etc.
Realçar:

200a relé de circuito integrado de alta frequência

,

240v relé de circuito integrado de alta frequência

,

Ssr 25 ampères

Descrição de produto

AC Single Phase SSR Solid State Relay AC SSR of Single Dual In line
 
 
 
 
Specification of  AC Single Phase SSR Solid State Relay
 
AC SSR of Single,Dual In-line
 

 

 

 

Main technical paramete

Type

SAQ2402DSAl4002D SAl4005D SAE4005D
Load voltage24-280VAC24-280VAC or 40-480VAC
Max Load current2A(Fig 1)2A(Fig 2)5A(Fig 3)8A(Fig 4)
Isolation bet.In & outOptical isolation ≥2000VAC 1min
Isolation to case≥2500VAC 1min
Control voltage3-15VDC or 15-28VDC
Control current6-25mA Need limit current
Turn-on voltage≤1.1VAC
Off-state leakage≤0.5mA
Off-state dv/dt300v/μs
On or off time10ms
Frequenty range47/63Hz
Operating temperature-50~80℃
Internal actual device(Triac)

3A

(Long-term current 1.2A)

6A

(Long-term current 1.5A)

12A

(Long-term current 2.5A)

16

(Long-term

current 5A)

ApplicationsContactor coil, Electromagnet, AC micro-motor, Heating. etc.

 
 
  
montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a 0
montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a 1
 

How to select a solid state relay
 
When selecting which solid state relay to use it is first necessary to define what it needs to be able to switch and how this needs to be achieved. There are a few useful steps to take and questions to ask:
 
AC or DC: There are different types of solid state relay used for switching AC or DC. Determining whether AC or DC power is to be switched is one of the most fundamental selections. As AC solid state switches typically use triacs and thyristors they do not work on DC and would not turn the load off, unless the DC falls to zero for some other reason. DC solid state switches typically use MOSFETs as they have a very low ON resistance.
 
Also remember that the input and output may be different - an SSR may be designed to control an AC output, but require a DC control voltage input, etc. In some instances a bridge rectifier, and possibly other electronic components may be required on the input to create the required control signal if they are not contained within the SSR package - check the specification to find out what may be needed.
Voltage range: It is necessary to determine the required voltage for the SSR. If DC is to be switched then select a solid state relay with at least 25% greater voltage rating than the maximum voltage anticipated. Ideally a greater margin would improve the reliability.
 
For AC SSRs, the AC voltage required for the application should be checked - again add a margin. Even though transients are present on many AC lines, AC solid state relays should be able to accommodate these as they are likely to have inbuilt protection (see below), but it is always best to check the specification.
Load current: Apart from the voltage, it is also necessary to know the current that will pass through the device. If too much current flows through the device then it will overheat and could be destroyed.
 
One point of which to be aware is the inrush current that many circuits exhibit. When first turned on, some items can draw levels of current that far exceed the average current drawn. It is therefore necessary to allow for this when selecting the solid state relay. Typically a multiplier is applied to the average current dependent upon the load which is being switched.
 
LOAD TO BE SWITCHED MULTIPLIER
Fluorescent lights (AC) 10
Incandescent light bulbs 6
Motors 6
Resistive heaters 1
Transformers 20
The average current to be consumed should be multiplied by the multiplier and the solid state relay chosen with this value for the current.
Dimming: If dimming is required, then some forms of solid state relay are able to provide a dimming function where the output is controlled by the level of the input.
Surge protection: If the solid state switch is to be used with AC, check that it has surge protection built in - most do be best to check. Surge or transient protection is normally provided using metal oxide varistors, MOVs. These metal oxide varistors absorb the transients and prevent them from damaging the SSR.
These points provide most of the major points to be considered when selecting a solid state relay. It is always good to read the whole of the SSR specification to ensure that there are no points that might adversely affect the operation of the overall circuit when in operation.
 
 
Solid state relays are ideal devices for many switching applications - they are faster and generally more reliable than electromechanical relays, although they are less resilient to transient spikes and other overload conditions.
 
In view of their superior operation in many scenarios, solid state relays are used in many circuits, with current and voltage ratings being available for many switching applications.

 
 
Our Company
 
Founded in 1992, Wuxi Gold Control Technology Co., Ltd., a private high tech company, is specialized in the research and production of Solid State Relays, Electronic Semiconductors, DC Motor Drivers and AC Voltage Regulation Devices.
 
For the past 10 consecutive years, our company has been qualified as "Jiangsu's private high tech business". We have also been given the honor as "Wuxi's 10 Best Private Science & Technology Enterprises" for years.
 
Our products, the electronic modules with the brand of Gold, have been listed among "Wuxi's Renowned Products".Our company has 5 patents on Solid State Relays. Our products are widely used in various industrial automation control areas like chemical fiber machinery, temperature control of electric furnace, rubber & plastic machinery, fountain control and digital-controlled machinery, and are sold to Europe, America, Korea and Turkey.
 
montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a 2
 
Our Factory
 
Our factory can produce about 50,000 pieces each month. We can give you good quality and reasonable prices. We have 20 professional research people who have all been graduated from famous universities and colleges. When producing, we have strict tests: self-test, inter-test and special-test.
 
    montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a 3
 
Our Certificate
 
Our products, the electronic modules with the brand of Gold, have been listed among "Wuxi's Renowned Products".Our company has 5 patents on Solid State Relays. Our products are widely used in various industrial automation control areas like chemical fiber machinery, temperature control of electric furnace, rubber & plastic machinery, fountain control and digital-controlled machinery, and are sold to Europe, America, Korea and Turkey.
 
Our company passed the Certification of ISO9001:2000 in 2000. Our main products have been given CE Certificate of European Union, UL,CUL and RoHS Certificates.
 
montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a 4
montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a 5
 

etiqueta:

Gold Relay State Solid

3-32VDC Single Phase SSR

Single Phase SSR 150a

Deseja saber mais detalhes sobre este produto
Estou interessado em montagem de alta frequência do trilho do ruído do relé de circuito integrado de 240v 200a você poderia me enviar mais detalhes como tipo, tamanho, quantidade, material, etc.
Obrigado!
Esperando sua resposta.